乐虎国际手机客户端为您免费提供乐虎国际手机客户端建筑检测鉴定公司建筑物纠偏和平移工程等相关信息发布和相关资讯,敬请关注!
新闻分类
联系我们

乐虎国际手机客户端

手机: 18660408530 (崔经理)
        检测鉴定/设计施工
        13210559279(赵经理)
        施工建材

电话: 0531-88987482

传真: 0531-88987482

邮箱:sdtqjiagusuo@163.com

网址:www.sdtqjz.com

地址: 山东省济南市高新区高新万达广场J1座2304室

您所在的位置:首页 > 行业新闻 > 详细内容
信息内容

钢筋乐虎国际静力切开厂家通知你“粘钢加固”

来源:/news/229.html  更新时间:2018-09-14
钢筋乐虎国际静力切开厂家通知你“粘钢加固”
Reinforced concrete static cutting manufacturer informed you "sticky steel reinforcement".
跟着人们生活质量的进步,关于住所环境和住所的房子质量愈加注重。而采纳正确的房子加固技能能够有用进步房子承载力,保证修建结构的巩固水平,然后更好地完成房子修建的运用功用。一般情况下,房子加固能够分为对损坏房子的维护性加固和进步房子损坏力的预防性加固。怎么通过粘钢加固房子?
With the improvement of people's quality of life, the quality of the housing environment and residence is more and more important. The adoption of the correct house reinforcement skills can effectively improve the bearing capacity of the house, ensure the level of consolidation of the building structure, and then better complete the use of building functions. In general, house reinforcement can be divided into maintenance reinforcement of damaged houses and preventive reinforcement of progressive house damage. How to strengthen the house by sticking steel?
粘钢加固
Bond steel reinforcement
粘钢加固施工流程
Construction process of bonded steel reinforcement
张贴面处理→钻螺栓孔→胶粘剂制造→涂胶和张贴→查验→维护
Surface treatment, drilling, bolt, hole, adhesive manufacture, glue and paste, inspection, maintenance.
1.张贴面处理
1. surface treatment
1.乐虎国际面应凿除点缀层,祛除油垢、污物,然后用角磨机打磨除掉1-2mm厚表层,较大凹陷处用找平胶修补平坦,打磨结束用压缩空气吹净浮尘,最后用棉布沾丙 酮拭净外表,待张贴面彻底枯燥后备用。
1. The concrete surface should be cut off the decoration layer, remove oil dirt, dirt, and then use a corner mill to grind away the 1-2 mm thick surface, the larger depression with leveling glue repair flat, grinding end with compressed air blowing dust, and finally with cotton cloth with acetone wipe clean the surface, until the surface is completely dry after the stand-by.
2.钢板张贴面运用角磨机进行粗糙、除锈处理,直至打磨呈现光泽,运用前若洁净仅用干布擦拭即可。否则可用棉布沾丙 酮拭净外表,待彻底枯燥后备用。
2. The surface of the steel plate is roughened and rusted by the angle grinder until it is polished and glossy. If it is clean before use, just wipe it with dry cloth. Otherwise, cotton can be wiped with acetone to wipe out the appearance.
3.该工序所用首要物资:护目镜、防尘口罩、冲击电锤及扁铲、手锤、角磨机、金刚石磨片、砂轮片、空压机、棉布、丙 酮。
3. Primary materials used in the process: goggles, dust masks, impact hammers and flat shovels, hand hammers, angle grinders, diamond grinding plates, grinding wheels, air compressors, cotton cloth, acetone.
2.钻螺栓孔
2. drilling bolt hole
加压固定可选用膨胀螺栓,需要在加固构件上合适方位钻孔固定膨胀螺栓。
The expansion bolt can be used for pressure fixing, and it is necessary to drill and fix the expansion bolt in the proper direction on the reinforcement component.
3.胶粘剂制造

3. adhesive manufacturing

乐虎国际手机客户端

1.修建结构胶为A、B两组份,取洁净容器(塑料或金属盆,不得有油污、水、杂质)和称重衡器按说明书合作比混合,并用拌和器拌和约5-10分钟至色泽均匀停止。拌和时好沿同一方向拌和,尽量防止混入空气形成气泡,装备场所宜通风杰出。
1. Construction of structural adhesive A, B two components, take clean containers (plastic or metal basins, no oil, water, impurities) and weighing weighing apparatus according to the specifications of the cooperation ratio, and mixing mixer for about 5-10 minutes until the color evenly stop. Mix well along the same direction in mixing, try to avoid mixing into the air to form bubbles, equipment sites should be ventilated outstanding.
2.该工序所用首要物资:拌和器、容器、衡器、腻刀、手套。
2. the main materials used in the process are mixer, container, weighing apparatus, knife and gloves.
4.涂胶和张贴
4. glue and paste.
1.胶粘剂制造好后,用腻刀涂改在已处理好钢板面上(或乐虎国际外表),胶断面宜成三角形,中心厚3毫米左右,边际厚1毫米左右,然后将钢板张贴在乐虎国际外表,用准备好的固定加压系统固定,恰当加压,以胶液刚从钢板边缝挤出为度。
1. After the adhesive is manufactured, apply greasy knife to the surface of the treated steel plate (or concrete surface), the cross-section of the adhesive should be triangular, the center thickness is about 3 mm, the marginal thickness is about 1 mm, then the steel plate is pasted on the surface of the concrete, fixed with the prepared fixed compression system, properly pressurized, and squeezed from the edge joint of the steel plate with glue. Out of degree.
2.该工序所用首要物资:腻刀、手套。
2. the main materials used in the process are knives and gloves.
5.查验
5. inspection
1.可用小锤轻击张贴钢板,从音响判别张贴作用,也可选用超生仪检测。若锚固区有用粘结面积少于90%,非锚固区有用粘结面积少于70%,应剥离钢板,从头张贴。
1., small hammer can be used to strike the steel plate, and the identification function should be judged from the sound. If the useful bonding area of anchorage zone is less than 90%, and that of non-anchorage zone is less than 70%, the steel plate should be stripped and pasted from scratch.
2.对重要构件也可选用载荷查验,一般选用分级加载至正常荷载的规范值,检测成果较直观、牢靠,但费用较高,耗时也较长。需要千斤顶或配重(常用沙袋、砖块)、百分表、裂缝显微镜、衡器。
2. Load inspection can also be used for important components. Normal values of normal loads are usually loaded by stages. The testing results are more intuitive and reliable, but the cost is higher and the time consuming is longer. You need jack or counterweight (commonly used sandbags, bricks), dial indicator, crack microscope, weighing instrument.
6.维护;加固后钢板宜选用20mm厚M15水泥砂浆抹面维护,也可选用涂防锈漆维护,以防止钢材的腐蚀。
6. Maintenance; After strengthening, steel plate should be selected 20 mm thick M15 cement mortar surface maintenance, can also choose to coat anti-rust paint maintenance, to prevent steel corrosion.
乐虎国际手机客户端,乐虎国际手机客户端对本站有兴趣的朋友可以关注我们
Shandong Tianqi Architectural Technology Co., Ltd., Shandong Reinforced Concrete Static Cutting Interested Friends can pay attention to our
相关标签:
相关新闻
相关产品